BS EN 61557 — Equipment for Testing, Measuring or Monitoring Protective Measures Series

Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. — Equipment for testing, measuring or monitoring of protective measures (IEC 61557, UK implementation)

⚡ BS EN 61557 is the BSI UK implementation of the IEC 61557 family “Electrical safety in low-voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. — Equipment for testing, measuring or monitoring of protective measures”, overseen by Technical Committee PEL/85 (Measuring equipment for electrical and electromagnetic quantities). The series sets unified requirements, measurement principles and uncertainty evaluation for electrical test instruments (insulation resistance testers, earth resistance testers, loop impedance testers, RCD test instruments, equipotential testers, fault locators, etc.) — the central basis for selecting and calibrating instruments used in low-voltage installation safety inspection (e.g. BS 7671 initial verification and periodic inspection). This batch of 16 files: Part 1 gives general requirements, and the subsequent parts give specific requirements for each measurement function. Published 2007–2015, it covers the full functional family of insulation, earthing, loop impedance, RCD, residual-current monitoring, fault location and equipotential testing across TN/TT systems.

💡 Three files (-1, -10, -11) are fully readable; the other 13 are scanned copies of the same series. Scanned content is written from the public-domain knowledge of IEC 61557 sub-part titles and low-voltage electrical testing — specific measurement uncertainty and test details must be taken from the official BSI edition.

1. Scope and General Framework 📌

The IEC 61557 family uses a “general + specific” structure:

  • Part 1 (General requirements): Defines common requirements for all equipment in the series, including safety (voltage category, overload), environmental conditions, marking, instructions and measurement-uncertainty evaluation rules.
  • Specific parts: -2 insulation resistance testing, -3 loop impedance testing, -4 resistance of earth conductors and equipotential bonds, -5 earth resistance testing, -6 RCD testing, -7 phase-sequence, -8 IT-system insulation monitoring (IMD), -9 fault-locating equipment, -10 combined measuring equipment, -11 general functions across systems. Parts 13–16 cover more specialist and monitoring equipment.
⚠️ Instrument grading and measurement uncertainty directly decide the confidence of inspection conclusions. Protective measurements accepted under BS 7671 (e.g. earth-fault loop impedance, RCD tripping time/current) must use instruments conforming to the relevant IEC 61557 part and properly calibrated; otherwise a compliant installation can be misjudged or a non-compliant item missed.

2. Series Composition and Key Points 🔧

Standard (BS EN 61557-)Measurement functionKey points
-1:2007General requirementsSafety, environment, marking, instructions, uncertainty (readable)
-2:2007Insulation resistanceTest voltage/range and discharge (scanned)
-3:2007Loop impedanceFault-loop impedance and prospective short circuit (scanned)
-4:2007Earth and equipotential resistanceEquipotential bond and earth continuity (scanned)
-5:2007Earth resistanceEarth resistance and auxiliary-electrode method (scanned)
-6:2007RCD measurementRated residual operating current/time, non-trip current (scanned)
-7:2007Phase-sequence indicationPhase sequence and rotation (scanned)
-8:2015IT-system insulation monitoring (IMD)Continuous insulation resistance monitoring (scanned)
-9:2015Fault-locating equipmentInsulation fault location (scanned)
-10:2013Combined measuring equipmentMultifunction tester function combination (readable)
-11:2009System functions (general)General measurement across systems (readable)
-12:2008 / -13:2011 / -14:2013 / -15:2014 / -16:2015Specialist monitoring and test equipmentResidual-current monitoring, special-parameter detection (scanned)

3. Key Technical Requirements 🔥

Building on the readable -1 (general), -10 (combined) and -11 (system functions), the key technical requirements are:

  • Uncertainty and grading (-1): Requires the manufacturer to state measurement uncertainty (e.g. ±(% of reading + digits)) and a uniform evaluation method, making conclusions traceable and comparable.
  • Safety design (-1): Specifies peak voltage, overload and external flashover protection by measurement category (CAT) and protection level, ensuring safe measurement on live circuits.
  • Specific measurement methods (-2 to -9): Insulation (-2) specifies test voltage and reading hold; loop impedance (-3) uses no-trip or reduced-leakage methods; RCD (-6) measures the boundary conditions of operating current ×0.5/×1 and operating time; earthing (-5) specifies auxiliary electrodes and their layout.
  • Combined and system functions (-10/-11): A multifunction instrument covering several measurements is classified as combined equipment without separately satisfying each specialist part; -11 defines system-generic functional requirements for unified verification.
  • Environment and EMC: Temperature, humidity, supply-voltage range and electromagnetic immunity are required to ensure reliable field use.
🚨 When testing an RCD, ensure the tester matches the RCD type: there are AC-type and also A-type (with DC component) and B-type RCDs. Using the wrong test waveform yields misleading trip/no-trip results and wrong conclusions about personal protection. Select the correct test mode per -6 and the RCD product standard.

4. Engineering Practice 🛠️

  • 🔍 Instrument selection: Per the BS 7671 measured items, determine the needed functions (insulation/earthing/loop/RCD/phase-sequence) and choose instruments conforming to the relevant BS EN 61557 part with calibration certificates.
  • 🔧 Initial and periodic inspection: On new installations, complete insulation, loop impedance, RCD characteristics and equipotential continuity tests per the BS 7671 schedule, then record and judge.
  • 📊 Calibration management: Maintain an instrument register and periodic calibration plan; the interval follows manufacturer advice and usage frequency to keep results valid.
  • 📋 Report and traceability: State instrument model, serial number, calibration validity and uncertainty in the inspection report for dispute review and system audit.

5. Frequently Asked Questions ❓

❓ Q: What is the relationship between BS EN 61557 and BS 7671?
A: BS 7671 is the wiring regulations (e.g. requiring earth-fault loop impedance within a limit); BS EN 61557 specifies the measuring instruments used to verify those requirements. They are the “requirement to be verified” and the “verification tool”.
❓ Q: Why doesn’t loop-impedance testing trip the RCD during test?
A: -3 uses a low-current / reduced-leakage or no-trip measurement principle to measure loop impedance safely without tripping the RCD, suited to live-circuit testing; after completion the RCD tester verifies its trip characteristic.
❓ Q: What do “×0.5, ×1, ×5” mean in RCD testing?
A: For the rated residual operating current IΔn, ×0.5 IΔn should not operate, ×1 IΔn must operate within the specified time (e.g. within 300 ms for incomers, 40 ms for sockets per BS 7671/product standard), and ×5 IΔn is used for instantaneous protection verification — the tester implements these points per -6.
🔍 Q: Can the scanned sub-parts be used directly for instrument development or calibration?
A: No. Instrument development, performance verification and calibration must use the official BSI current edition; scanned parts only help understand the functional family and sub-part positioning.
🔒
正在加载下载地址,请稍候 10 秒

Leave a Reply

Your email address will not be published. Required fields are marked *