BS EN 61375 — Electronic Railway Equipment Train Communication Network (TCN)

Electronic Railway Equipment — Train Communication Network (TCN) (IEC 61375 series)

🚄 The BS EN 61375 series is the British Standard implementation of EN 61375, which is identical to IEC 61375. It defines the Train Communication Network (TCN) for the transfer of data between electronic equipment on board railway vehicles and across a train. The TCN is the shared “nervous system” for train control, diagnostics, passenger information and multimedia, and its standardisation is central to interoperability between different manufacturers’ equipment and to safe train operation.

💡 The value of TCN standardisation is clear: as long as equipment complies with EN/IEC 61375, vehicle control units, gateways and displays from different suppliers can interconnect on the same train, sharply reducing integration cost and spare-part dependency.

1. Series Overview 📌

The BS EN 61375 series is organised into a general architecture part (Part 1), train-level bus parts (Part 2-x) and consist/multimedia network parts (Part 3-x). Part 1 defines the overall TCN architecture and terminology; Part 2-1 defines the Wire Train Bus (WTB) and Part 2-2 gives its conformance testing; Parts 3-x address the consist network and multimedia systems. The UK committee is GEL/9 (Railway Electrotechnical Applications) through panel GEL/9/-/4.

⚠️ Parts 2-3, 2-5 and Parts 3-1 to 3-4 in this series are scanned versions; the related descriptions here are compiled from public domain knowledge of the standard’s field, and the authoritative text is the official BSI published version.

2. Series Structure and Technical Points 🧩

The series contains 9 standard documents, as shown below.

Standard No.EditionSubject (English title)
BS EN 61375-12012Part 1: General architecture
BS EN 61375-2-12012Part 2-1: Wire Train Bus (WTB)
BS EN 61375-2-22012Part 2-2: Wire Train Bus conformance testing
BS EN 61375-2-32015Part 2-3: Communication protocol related parts (scanned)
BS EN 61375-2-52015Part 2-5: Communication protocol related parts (scanned)
BS EN 61375-3-12012Part 3-1: Consist / multimedia network (scanned)
BS EN 61375-3-22012Part 3-2: Consist / multimedia network (scanned)
BS EN 61375-3-32012Part 3-3: Consist / multimedia network (scanned)
BS EN 61375-3-42014Part 3-4: Consist / multimedia network (scanned)

BS EN 61375-1:2012 is identical to IEC 61375-1:2012 (3rd edition), prepared by IEC/TC 9 “Electrical equipment and systems for railways”, with ICS 45.060 (railway rolling stock).

3. Key Technical Requirements 🔧

3.1 General architecture

Part 1 establishes the layered and topological concepts of the TCN: at train level the WTB connects the vehicles, while within a consist the consist network (MVB / Ethernet consist network and so on) connects the devices, forming a train–consist–device hierarchy, and it defines addressing, real-time behaviour, redundancy and fault detection requirements.

3.2 Wire Train Bus (WTB)

Part 2-1 defines the physical, data-link and application layers of the WTB, including the bus medium (screened twisted pair), transmission rate, frame format, node addressing, master–slave polling and token mechanisms. The WTB supports automatic reconfiguration when trains are coupled, making it the backbone of train-level information exchange.

3.3 Conformance testing

Part 2-2 specifies the test items, methods and acceptance criteria for WTB conformance, covering physical-layer parameters, protocol behaviour, timing, fault injection and boundary conditions, to verify that a device genuinely complies with the WTB specification.

🚨 Conformance testing is a critical gate for TCN equipment entering service. Even a functionally correct device that has not passed conformance testing may cause whole-train communication failures due to protocol behaviour differences, so type testing to Part 2-2 should be performed strictly.

4. Practical Engineering Application 🛠️

  • 🔍 Network selection: choose WTB or Ethernet TCN according to train size and real-time requirements, and match the applicable part of the standard.
  • 🔧 Gateways and interfaces: vehicle control units (VCUs) connect to the WTB through gateways, and must implement address allocation, message mapping and redundancy switching as specified.
  • 📊 Interoperability verification: before a train enters service with equipment from different suppliers, joint commissioning and conformance testing should be carried out to ensure consistent protocol stacks, timing and diagnostic information.
  • 📋 Fault diagnosis: use TCN diagnostic messages to localise train-level faults and shorten maintenance time.

5. Frequently Asked Questions ❓

❓ Q: What is the difference between the WTB and the consist bus?
A: The WTB is the train-level bus crossing vehicles and connecting gateways and vehicle control units of the whole train, supporting automatic reconfiguration after coupling. The consist bus (for example MVB or Ethernet consist network) connects devices within a consist or vehicle, with different real-time and bandwidth requirements.
❓ Q: Why is conformance testing necessary?
A: The TCN involves interconnection of equipment from many suppliers; functional correctness alone does not guarantee identical protocol behaviour. Conformance testing validates compliance with the specification through standardised tests and is the basis of interoperability.
❓ Q: How does BS EN 61375 relate to Ethernet train networks?
A: The 61375 series includes both the traditional WTB/MVB scheme and an Ethernet-based TCN (for example Parts 2-3 and 3-x) to meet high-definition video, large data volumes and tighter real-time needs. The applicable part of the standard governs the choice.
🔍 Q: How does the network reconfigure when trains are coupled?
A: The WTB has automatic consist/addressing capability. After coupling, the new train topology is detected automatically, the gateway reassigns node addresses and establishes communication without manual intervention.
🔒
正在加载下载地址,请稍候 10 秒

Leave a Reply

Your email address will not be published. Required fields are marked *