BS EN 60669 — Switches for Household and Similar Fixed Electrical Installations Standard Series

Switches for Household and Similar Fixed Electrical Installations (EN 60669 series, identical to IEC 60669)

💡 BS EN 60669 is the European Standard series on switches for household and similar fixed electrical installations, whose technical content is identical to IEC 60669 (including CENELEC common modifications). It covers the wall switches we use every day, electronic touch switches, remote-control switches, time-delay switches, isolating switches, and the special switches used in building automation systems (HBES) and fire scenarios. It is one of the broadest standard families in the electrical-accessory field; its Part 1 also retains the secondary numbering of the contemporary BS 3676.

💡 The switches in a building are far more than “on and off”: from an ordinary rocker switch to an electronic remote-control switch, to a fireman’s switch cutting off sign illumination, BS EN 60669 legislates by functional type, and electrical designers and electricians must select the corresponding part according to the application scenario.

1. Overview and Background 📌

The IEC 60669 series was developed by IEC TC 23 (Electrical accessories) and its SC 23B, adopted by CENELEC as EN 60669 with European common modifications, and then published by BSI as British Standards (for example BS EN 60669-1:1999+A2:2008). The series early referenced the British BS 3676, and its edition history continually absorbed new technologies such as electronic switches and building automation (for example Part 2-2 explicitly excludes electronic remote-control switches, later handled by subsequent parts). The UK participates through PEL/23 (Electrical accessories).

⚠️ Parts 2-3, 2-4, 2-5 and 2-6 of this series exist as scanned copies in the source material; their technical content has been compiled from public-domain knowledge. Refer to the latest official BSI version for electrical safety requirements.

2. Structure of the Series 📑

StandardSubjectContent Focus
BS EN 60669-1:1999+A2:2008General requirementsGeneral requirements and tests for conventional mechanical switches
BS EN 60669-2-1:2004+A12:2010Electronic switchesGeneral and safety requirements for electronic switches
BS EN 60669-2-2:2006Electromagnetic remote-control switches (RCS)Electromagnetic RCS (excluding electronic)
BS EN 60669-2-3:2006Time delay switches (TDS)Timed/delayed control switches
BS EN 60669-2-4:2005Isolating switchesSwitches for isolating the supply
BS EN 60669-2-5:2016Switches for HBESSwitches for home and building electronic systems
BS EN 60669-2-6:2012Fireman’s switchesFire cut-off switches for sign lighting, etc.

3. Key Technical Content 🔧

3.1 General Requirements (Part 1)

Part 1 specifies the general construction and safety requirements of household wall switches: rated voltage/current, mechanical operation and endurance, temperature rise, heat and fire resistance, dielectric strength (voltage withstand), creepage distances and clearances, protection against electric shock, and marking and instructions. CENELEC common modifications and interpretation sheets (such as the June 2009 sheet) are reproduced as national annexes.

3.2 Electronic and Remote-Control Switches (Parts 2-1, 2-2)

Part 2-1 adds electromagnetic-compatibility, fault-condition and more stringent temperature-rise requirements for switches with electronic circuits (touch, radio reception, dimming semiconductors). Part 2-2 addresses electromagnetic remote-control switches (RCS), whose control and main circuits are separated, requiring assessment of the coil circuit and control distance.

3.3 Time-Delay, Isolating and Smart-Building Switches (Parts 2-3, 2-4, 2-5)

Time-delay switches (TDS) are used for automatic switch-off in corridors etc., requiring assessment of set time and repeated operation. Isolating switches must reliably disconnect for maintenance. HBES switches (Part 2-5) are for switches integrated into the bus system of smart buildings, involving coordination of communication and supply safety.

3.4 Fireman’s Switches (Part 2-6)

Fireman’s switches cut off the supply to outdoor advertising and sign lighting, operated by firefighters during an incident. The Standard specifies their identification (red), operating force and disconnection reliability, so firefighters can find and operate them quickly in an emergency.

🚨 Safety note: isolating switches and ordinary switches must not be confused. Only products identified as an isolating switch may be used as the “all-pole disconnection” device for maintenance; an ordinary switch has no isolating function, and misuse creates a live-maintenance risk.

4. Engineering Practice and Applications 🛠️

  • 🔍 Electrical-accessory manufacturers: perform general type tests under Part 1, then apply the specific clauses of the Part 2-x according to product function, forming a complete certification file.
  • 🔧 Building electrical design: use time-delay switches (2-3) in corridors/car parks, isolating switches (2-4) on maintenance circuits, HBES switches (2-5) for smart homes, and fireman’s switches (2-6) for outdoor sign lighting per fire requirements.
  • 📊 Testing and certification: focus on the EMC, temperature-rise and fault tests of electronic switches (2-1), and the control characteristics of remote-control switches (2-2).
  • 📋 Property and maintenance: periodically check the reachability and marking of fireman’s switches to ensure reliable emergency disconnection.

5. Frequently Asked Questions ❓

❓ Q: How do BS EN 60669 and BS 3676 relate?
A: Part 1 retained the secondary identifier BS 3676-1; it is a different numbering of the same technical content. The current effective version should be used in application.
❓ Q: Why do electronic switches have their own part?
A: Electronic switches contain semiconductor circuits whose failure modes, EMC and temperature-rise behaviour differ greatly from mechanical switches; a separate part gives more targeted safety requirements.
❓ Q: What must be assessed for a time-delay switch (TDS)?
A: The accuracy of the set delay time, the reliability of repeated operation, and the safe state after mis-operation or power loss during the delay period.
🔍 Q: Why must a fireman’s switch be “red”?
A: Part 2-6 requires its marking and colour to be easily identifiable; a red marking helps firefighters find and operate it quickly in smoke and emergencies.
🔒
正在加载下载地址,请稍候 10 秒

Leave a Reply

Your email address will not be published. Required fields are marked *