BS EN ISO 10534 — Determination of Sound Absorption Coefficient and Impedance in Impedance Tubes

Acoustics — Part 1: Standing wave ratio method; Part 2: Transfer-function method

🎵 BS EN ISO 10534 specifies methods for determining the sound absorption coefficient and normal acoustic impedance of materials using an impedance tube (standing-wave or acoustic tube). It is a fundamental standard in building acoustics, material acoustics, and noise control. The series has two parts: BS EN ISO 10534-1 uses the standing wave ratio method, and BS EN ISO 10534-2 uses the transfer-function method. Both rely on the plane-wave acoustic theory of sound propagation in a rigid-wall tube, reconstructing the normal incidence absorption coefficient and normal acoustic impedance of a specimen from the standing wave field or transfer function measured in the tube.

💡 The absorption coefficient α is the fraction of incident sound energy absorbed by the material (0 to 1); the normal acoustic impedance describes how the material surface resists the incident wave. These are core parameters for sound insulation, absorption, silencer design, and acoustic performance evaluation.

1. Series Overview and Scope 📌

In the UK this series is the responsibility of subcommittee EH/1/6 (Building acoustics). It was prepared by ISO/TC 43 “Acoustics” with CEN/TC 126. BS EN ISO 10534-1:2001 is identical to ISO 10534-1:1996, was approved by CEN in June 2001, and published as a British Standard on 2 November 2001; BS EN ISO 10534-2:2001 is identical to ISO 10534-2:1998, was approved by CEN in June 2001, and implemented in the UK on 11 April 2002 (Amd. 13701).

PartSubjectICSISO EquivalentMethod
BS EN ISO 10534-1:2001Standing wave ratio method91.120.20; 17.140ISO 10534-1:1996Determines absorption coefficient and impedance from the standing-wave ratio
BS EN ISO 10534-2:2001Transfer-function method17.140.01ISO 10534-2:1998Two-microphone transfer function determines absorption coefficient and impedance
⚠️ Both methods rely on the plane-wave assumption, so the upper test frequency is limited by the tube diameter (the diameter must be much smaller than the wavelength). Above the limit, higher-order modes appear and the results become unreliable.

2. Standing Wave Ratio Method (Part 1) 🔧

In the standing wave ratio method the specimen is placed at one end of the tube and a loudspeaker at the other. The loudspeaker excites a plane wave; the incident wave and the reflected wave from the specimen combine into a standing wave. A traversing probe microphone moves along the tube axis and measures the maximum sound pressure pmax and minimum pmin, giving the standing-wave ratio n = pmax/pmin, from which the absorption coefficient and normal acoustic impedance are calculated.

The method measures at discrete frequencies and requires point-by-point scanning at each test frequency, so it is relatively slow, but the equipment is simple and the principle intuitive — well suited as a reference or arbitration method. The Standard specifies specimen size, mounting, probe traverse accuracy, wall rigidity, and frequency range.

3. Transfer-Function Method (Part 2) 🔩

The transfer-function method uses two microphones at fixed positions to measure the sound pressure at two points simultaneously; the transfer function, together with the tube geometry and acoustic parameters, is used to reconstruct the specimen’s normal absorption coefficient and acoustic impedance. Compared with the standing wave method, no point-by-point scan is needed — a full continuous spectrum is obtained in one broadband measurement, giving higher speed and accuracy. It is now the routine laboratory method.

The Standard sets strict requirements for microphone spacing, microphone-to-specimen distance, tube diameter, environmental conditions (temperature, humidity, pressure) and calibration, to ensure accuracy and repeatability. Tests typically cover roughly 50 Hz up to 10 kHz or higher, depending on tube size and microphone layout.

ComparisonStanding Wave Ratio (Part 1)Transfer Function (Part 2)
Measurement modePoint-by-point scan, discrete frequenciesBroadband continuous measurement
MicrophonesSingle traversing probe microphoneTwo fixed microphones
SpeedSlowerFaster
Best suited forReference/arbitration, simple materialsRoutine testing, spectral analysis

4. Specimen Requirements and Measurement Conditions 🛠️

To ensure comparability and repeatability the Standard specifies specimen preparation and mounting: the specimen must represent the actual product state, with thickness, density, porosity, etc. consistent with the real product; it must be flat and mounted tightly against the rigid back plate at the tube end with no edge leakage. Porous materials (mineral wool, glass wool, polyurethane foam) and fibrous materials should keep their original structure without compaction or distortion.

  • Specimen size: must fully cover the tube cross-section, with diameter matching the internal tube diameter.
  • Mounting: back plate should be rigid and non-absorbing; specimen-to-wall seal should be good.
  • Environment: record temperature, relative humidity and atmospheric pressure, correcting sound speed as required.
  • Calibration: the system (including microphones) should be calibrated regularly for frequency and phase response.

5. Engineering Application Practice 🌐

Impedance-tube testing is widely used for acoustic performance evaluation and quality control of building acoustic materials, automotive interiors, aircraft cabins, and industrial silencers. In building acoustics the absorption coefficient is used to calculate reverberation time, design room acoustics, and control noise; in silencer design the normal acoustic impedance is a key input for computing insertion loss and optimising structure.

🚨 Impedance-tube testing gives the normal-incidence absorption coefficient and normal impedance, which differ from the random-incidence absorption coefficient measured in a diffuse field (e.g., reverberation room). Always state which definition is used in applications to avoid design errors.

6. Frequently Asked Questions ❓

❓ Q: Which is more common, the standing wave ratio or the transfer-function method?
A: The transfer-function method (Part 2) is faster and covers a broad band continuously, so it is the routine laboratory method; the standing wave ratio method (Part 1) is simpler and often used for reference and arbitration.
❓ Q: Can the impedance-tube absorption coefficient be used directly in reverberation-room acoustic design?
A: No. The tube gives the normal-incidence coefficient; the reverberation room gives the random-incidence coefficient. The conversion is complex and usually requires correction for thickness, mounting and frequency.
❓ Q: Why is the upper test frequency limited by the tube diameter?
A: Only when the tube diameter is much smaller than the wavelength can plane-wave propagation be maintained. Above the limit higher-order modes appear and the plane-wave assumption breaks down, making results unreliable.
❓ Q: Can this series measure the flow resistivity of porous materials?
A: No — this series measures absorption coefficient and acoustic impedance. Flow resistivity, another parameter characterising the permeability of porous materials, is measured separately (e.g., ISO 9053).
🔒
正在加载下载地址,请稍候 10 秒

Leave a Reply

Your email address will not be published. Required fields are marked *