The “Dictionary” of the PCB Industry — Standardized Definitions for Pads, Vias, and Solder Mask IEC 60356:1971 is an early printed circuit board terminology standard. Though later supplemented by the more comprehensive IEC 60194 series, its fundamental term system (Land/Pad,…

Waveguide Flanges — How Mechanical Precision Determines Electrical Performance IEC 60374:1971 specifies waveguide and waveguide component flange standardized dimensions. Flange flatness (typically ≤0.01 mm) and alignment pin precision directly determine the connection VSWR — every 0.1 mm increase in flange…

Storage vs. Instantaneous Water Heaters — Why Efficiency Numbers Cannot Be Directly Compared IEC 60379:1987 specifies household electric water heater performance measurement. Storage heater efficiency is dominated by standby heat loss — an 80L tank loses 1.5–2.5 kWh Instantaneous heaters…

“Wow and Flutter” — The Most Annoying Sound Distortion of the Analogue Era and Its Measurement IEC 60386:1972 specifies magnetic tape recorder speed stability measurement. Flutter (>10 Hz) and Wow (

The “Safety Bible” Behind Every Appliance — IEC 60335-1 Seven Safety Dimensions IEC 60335-1 is the household and similar appliance safety general requirements standard — the benchmark for safety certification of hundreds of billions of appliances globally. It covers electric…

Why Tropical Regions Have Higher Electrical Failure Rates — Humidity Effects on Insulation IEC 60345:1971 specifies insulation resistance measurement under humid conditions. Polar insulating materials (phenolic, nylon) at 95% RH adsorb just a few molecular layers of water, and surface…

Oscilloscopes From 100MHz to 100GHz — The Dual Engine of Analogue Bandwidth and Sample Rate IEC 60351-2:1976 specifies oscilloscope performance and testing. Oscilloscopes evolved from analogue CRT→DSO→MSO→real-time ≥100 GSa Analogue bandwidth is determined by the front-end amplifier -3dB point; digital…

How Many Insulator Discs Does a 500kV Line Need? Precision Calculation of Creepage Distance and Pollution Class IEC 60383-2:1993 specifies overhead line insulators above 1,000V AC. Number of discs = (Um × specific creepage) / single-disc creepage. China Class I…

Transformer Insulation Paper Is Not Ordinary Paper — It Is Vacuum-Impregnated Cellulose or Aramid Fibre IEC 60394-1:1972 specifies impregnated fabrics for electrical purposes. The “insulation paper” used in transformers and motors is actually specialty cellulose (Kraft) or aramid (Nomex) fibre…

How Much Can You Overload a Transformer? IEC 60354 Temperature and Ageing Models IEC 60354:1991 specifies oil-immersed power transformer overloading guidance. Nameplate ratings assume continuous full load, 30°C ambient, normal life. Under low ambient temperature, short-duration overload, or preceding low…

Crushed Magnetic Cores — One of the Most Common Mechanical Failures in SMPS IEC 60373:1990 specifies ferrite core mechanical property testing. Ferrite is a brittle ceramic — under combined winding tension (hundreds to thousands of grams), impregnation varnish curing shrinkage,…

Why Industrial Sensors Use 4-20mA, Not 0-10V — The Current Loop Noise Immunity Advantage IEC 60381-2:1978 specifies process control analogue signal standard ranges — 4-20mA DC current loop. Compared to voltage signals (0-10V), current loops offer three advantages: (1) EMI…

Why Pneumatic Control Signals Are 3-15 psi, Not 0-15 psi — The Same “Live Zero” Philosophy as 4-20mA IEC 60382:1991 specifies process control pneumatic signal standard ranges — 3-15 psi (20-100 kPa). 3 psi (not 0) as the zero-scale point…

Why Some Switches Work Only on AC, Not DC — Arc Quenching Determines Everything IEC 60328 specifies household appliance switch requirements. A switch rated “10A 250VAC” cannot be used at 10A 48VDC — DC arcs have no natural zero-crossing for…

Is Your Washing Machine Interfering With the Neighbour Radio? Household Appliance EMC Limits IEC 60341 specifies household appliance radio interference limits and measurement. Every appliance with a motor, SMPS, or microprocessor injects HF noise (150 kHz–30 MHz) into the mains…

Why Cable DC Resistance Is the “Double Mirror” of Copper Purity and Cross-Section IEC TR 60344:2007 specifies low-frequency cable conductor DC resistance calculation and measurement guidance. R₂₀=ρ₂₀×L/A — if measured value exceeds nominal, only two explanations: (1) copper purity insufficient…

How PLC Signals Are “Trapped” on One Line — The Line Trap Working Principle IEC 60353:1989 specifies line trap requirements. A line trap is a parallel resonant circuit (main coil L + tuning capacitor C) inserted at the HV line…