BS EN ISO 07784 — Paints and Varnishes Determination of Resistance to Abrasion (Abrasive-Paper Wheels, Rubber Wheels and Linear Reciprocating)

Paints and Varnishes — Determination of Resistance to Abrasion: Part 1 / Part 2 / Part 3 (BS EN ISO 7784 series)

🛞 BS EN ISO 07784 (ISO 7784) is the standard series for determining the resistance to abrasion of paints and varnishes (coatings), defining three abrasion test methods for evaluating coating durability under friction, scratching, and abrasive action. This batch covers three parts: Part 1 is the method with abrasive-paper covered wheels and a rotating test specimen, Part 2 is the method with abrasive rubber wheels and a rotating test specimen, and Part 3 is the method with an abrasive-paper covered wheel and a linearly reciprocating test specimen. Developed jointly by ISO/TC 35 (Paints and varnishes) and CEN/TC 139 (Paints and varnishes) and adopted by BSI as a British Standard, it is widely used for evaluating the abrasion resistance of wood coatings, floor coatings, automotive paints, and industrial coatings.

💡 Resistance to abrasion is one of the most visible durability indicators of a coating in service: floor, furniture, vehicle, and industrial-equipment surface coatings are subjected to foot traffic, friction, and abrasive scouring over time. ISO 7784 converts “abrasion resistance” into a repeatable, comparable value through standardised wheels/abrasives and load, providing a basis for formulation screening and quality acceptance.

1. Series Overview and Scope 📌

StandardTitleYear
BS EN ISO 7784-1:2016Method with abrasive-paper covered wheels and rotating test specimen2016
BS EN ISO 7784-2:2016Method with abrasive rubber wheels and rotating test specimen2016
BS EN ISO 7784-3:2016Method with abrasive-paper covered wheel and linearly reciprocating test specimen2016

The three methods share the same principle: under a specified load and speed, the abrasive wheel or abrasive makes relative motion with the coating surface; after a specified number of revolutions or reciprocations, the abrasion resistance is judged by the coating mass loss or the number of cycles to wear-through. Parts 1 and 2 use a rotating specimen (the specimen rotates about a vertical axis while the wheels are fixed or counter-rotate), while Part 3 uses linear reciprocating motion of the specimen with a rolling abrasive-paper covered wheel, suiting different specimen shapes/sizes and different wear conditions.

⚠️ Result-expression note: the methods give different indicators — mass loss (mg per 1000 cycles, etc.), volume loss, or the number of cycles to a specified wear-through state. Always state the method and indicator when citing; otherwise data are not comparable — small differences in wheel, abrasive, and load also markedly affect results.

2. Series Composition and Technical Points 🔧

2.1 BS EN ISO 7784-1: Abrasive-Paper Covered Wheels and Rotating Specimen

This part uses two abrasive-paper covered wheels (e.g., Taber type); the specimen is mounted on a rotating platform at a specified speed (e.g., 60 r/min or 72 r/min), and the wheels produce an annular wear track on the specimen surface. Abrasion resistance is evaluated by the mass difference of the specimen (coating) before and after the test, or by measuring the wear-track depth. This method is commonly used for wood, plastic, and general industrial coatings; the abrasive (paper grit) and load are chosen per the standard.

2.2 BS EN ISO 7784-2: Abrasive Rubber Wheels and Rotating Specimen

This part uses two rubber wheels containing abrasive particles (e.g., CS-10/CS-17 type) with a rotating specimen. The elastic contact of the rubber wheel better approximates real wear conditions (foot traffic, sole friction), and the wheel itself combines “abrasive cutting + elastic deformation” in a compound wear action. Results are expressed as mass loss (mg) or volume loss, suiting evaluation of floor paints, floor coatings, and coatings with higher abrasion-resistance requirements.

2.3 BS EN ISO 7784-3: Abrasive-Paper Covered Wheel and Linearly Reciprocating Specimen

This part uses linear reciprocating wear: the specimen is fixed on a platform moving in a linear reciprocating motion, while an abrasive-paper covered wheel rolls over the specimen surface under a specified load, leaving a linear wear track. The method suits larger or specially shaped specimens and cases requiring simulation of unidirectional scratching/wear (e.g., door slides, furniture edges); it is evaluated by mass loss or wear-through cycles.

💡 Method selection: for general coating comparison use the rotating method (Part 1, abrasive paper); for elastic-contact wear, floor and flooring paints use the rubber-wheel method (Part 2); for linear scratch conditions, or specimens unsuitable for rotation, use the reciprocating method (Part 3). Fix the method and parameters within a product family to keep results comparable.

3. Key Technical Requirements and Test Elements 🎯

  • Specimen and coating preparation: apply the coating to the substrate per the product specification and cure (dry) fully, with uniform film thickness and no defects; condition per the standard before testing.
  • Wheels and abrasives: the abrasive-paper grit / rubber-wheel type, wheel hardness, and abrasive type are set per the standard; wheels should be pre-worn (broken in) before use and replaced or dressed periodically to keep wear conditions consistent.
  • Load and speed: set the normal load on the specimen (e.g., 5 N, 10 N, etc.) and the specimen rotation/reciprocation speed per the standard; apply the load smoothly and uniformly.
  • Cycles and wear track: run the specified number of cycles (or until wear-through); measure the mass loss (precise weighing) or the wear-track depth/wear-through cycles; the wear track should lie within the effective area of the specimen.
  • Result calculation and reporting: report mass loss (mg) or volume loss (mm³, converted using the coating density), noting the wheel, load, cycles, and abrasive type.
🚨 Safety: abrasion testing generates dust and debris — work in a ventilated area and wear goggles and a dust mask; never touch the high-speed rotating wheels by hand; clamp the specimen firmly to prevent ejection; observe fire and ventilation precautions when handling solvent-borne coatings and cleaning agents.

4. Engineering Practice and Applications 🛠️

  • Coating formulation development: compare different resin, filler, wax, and additive systems by abrasion tests to optimise the formulation for higher abrasion and scratch resistance.
  • Product quality acceptance: wood coatings, floor coatings, automotive paints, and industrial topcoats undergo abrasion inspection per product standards to judge compliance with abrasion-grade requirements.
  • Failure and service-condition simulation: reproduce abrasion failures of coatings to identify the wear mechanism (abrasive wear, fatigue spalling) and propose improvements.
  • Standard and specification reference: product technical specifications in construction, transport, and appliance industries cite ISO 7784 for abrasion indicators as a basis for procurement and acceptance.

5. Frequently Asked Questions ❓

❓ Q: Which is more common, mass loss or volume loss?
A: Mass loss (mg) is the simplest to measure and the basic indicator in most abrasion standards; however, different coatings have different densities, so converting to volume loss (mm³) allows fairer comparison across coatings of different density — hence high-precision evaluation often reports both mass and volume loss.
🔍 Q: Can the abrasive-paper-wheel and rubber-wheel methods be compared directly?
A: Not directly. The abrasive-paper wheel is mainly hard abrasive cutting, while the rubber wheel is elastic-contact compound wear; the mechanisms differ and the numerical results differ substantially. Choose the method appropriate to the service condition and compare relatively with fixed method parameters.
❓ Q: Why must the wheels be “broken in”?
A: New wheels have an uneven surface and non-uniform abrasive distribution, so the first run gives unstable results. Breaking in (conditioning) brings the wheel surface to a stable wear state before the formal test, ensuring comparability between specimens on the same wheel and between different wheels.
🔍 Q: Does coating film thickness greatly affect the abrasion result?
A: Yes. Insufficient film thickness may wear through prematurely to the substrate; excessive thickness masks the intrinsic abrasion resistance of the coating; and thickness differences change the mass per unit volume. Control the film thickness uniformly and note the dry film thickness in the report for comparability.
🔒
正在加载下载地址,请稍候 10 秒

Leave a Reply

Your email address will not be published. Required fields are marked *